mtk UART代码修改配置

可以修改文件nvram_common_config.c中NVRAM_EF_PORT_SETTING_DEFAULT的配置。

注意检查MMI版本和宏的开启情况。

static port_setting_struct const NVRAM_EF_PORT_SETTING_DEFAULT[]=
{
{
#if defined (WISDOM_MMI) || defined(NEPTUNE_MMI)
0, /* tst-ps uses uart_port2(value is 1) */
1, /* APP uses uart_port1 (value is 0) */
#elif defined(__USB_MULTIPLE_COMPORT_SUPPORT__) && defined(__L4_INIT_MULTIUSB_COM__)
0, /* TST-PS uses uart_port1 */
5, /* ATCI uses uart_port_usb2 */
#else
0, /* tst-ps uses uart_port_null(value is 99) */ //配置tst-ps ，可用于连catcher抓log，0表示uart1，1表示uart2，...依此类推，99表示none
1, /* APP uses uart_port1 (value is 0) */ //配置ps，可用于通AT的uart口

#endif

#if defined(EMPTY_MMI) //tst-ps的波特率设置，连catcher的话，catcher必须配置一致，如果是modem，就是EMPTY_MMI
921600, /* tst default baud rate for project without MMI */
#elif defined (WISDOM_MMI)
/* under construction !*/
#elif defined(__USB_MULTIPLE_COMPORT_SUPPORT__) && defined(__L4_INIT_MULTIUSB_COM__)
921600, /* TST-PS baud uses 921600 */
#else
115200, /* tst default baud rate base = 115200 = 0x0001C200 */
#endif

#if defined (__PS_SERVICE__) //ps的波特率设置，例如连超级终端下AT，超级终端com口的波特率必须与此配置一致
961200, /* ps default baud rate base = 115200 = 0x0001C200 */
#else
57600, /* ps default baud rate base = 57600 = 0x0000E100 */
#endif

KAL_FALSE, /* High SpeedSIM */
0, /* SWDBG */
#if defined(__ONLY_ONE_UART__)
1, /* uart power setting (0x03) */
#else
3,
#endif

99, /* CTI uart port: uart_null (value is 0x63 (99) */
0, /* CTI baud rate: auto*/

#if defined (WISDOM_MMI) || defined(NEPTUNE_MMI)
0,
#elif defined(__USB_MULTIPLE_COMPORT_SUPPORT__) && defined(__L4_INIT_MULTIUSB_COM__)
1, /* TST-L1 baud uses uart_port2 */
#else
0, /* tst-l1 uart port, same as tst-ps*/ //配置tst-L1，与tst-ps的配置一致
#endif

#if defined(EMPTY_MMI) //tst-L1的波特率设置，与tst-ps的波特率一致
921600, /* tst default baud rate for project without MMI */
#elif defined (WISDOM_MMI)
/* under construction !*/
#elif defined(__USB_MULTIPLE_COMPORT_SUPPORT__) && defined(__L4_INIT_MULTIUSB_COM__)
921600, /* TST-L1 baud uses 921600 */
#else
115200, /* tst default baud rate base = 115200 = 0x0001C200 */
#endif

0, /* tst output mode*/
#if !defined( __UL1_STANDALONE__ )
0, /* USB logging mode */
#else
#if defined(__MODEM_3G_LOGGING__) && defined(_DSPIRDBG__)
/* under construction !*/
#else
1,
#endif /* defined(__MODEM_3G_LOGGING__) && defined(_DSPIRDBG__) */
#endif /* __UL1_STANDALONE__ */

99, //TST-DSP
921600, //TST-DSP baudrate

0 // USB CD-ROM config, 0:CD-ROM , 1: COM
},
};